 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| om .c 4U SMT Wide Input, 3W et Single & e Dual Output Sh verters DC/DC Con ta a Electrical Specifications D . w Key Features: w w Input Parameter LF300RW Series Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. 3W Output Power UL Approved (File E245422) Wide 2:1 Inputs Miniature SMT Case Tight Line/Load Regulation 1,500 VDC Isolation -40C to +70C Operation 21 Standard Models 1.0 MH MTBF Minimum Industry Standard Pin-Out Input Start Voltage Conditions 12 VDC Input 24 VDC Input 48 VDC Input Min. 4.5 8.0 16.0 Reverse Polarity Input Current Short Circuit Input Power Input Filter (Pi) Filter Conditions Output Parameter Output Voltage Accuracy Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) (Note 1) Ripple & Noise (20 MHz) Ripple & Noise (20 MHz) Output Power Protection Transient Response Time (Note 2) Transient Response Deviation Temperature Coefficient Output Short Circuit Dual Output, Balanced Load For Vin = Min to Max Iout = 20% to 100% General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA w w Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity .D w t a S a e h t e U 4 .c m o Typ. 0.5 0.5 0.1 0.3 50 120 250 2.0 0.01 Typ. 6.0 12.0 24.0 Max. 8.0 16.0 32.0 0.5 1,500 Units VDC A mW Min. Max. 1.0 1.0 0.3 1.0 75 100 10 500 6.0 0.02 25% Load Step Change Continuous Conditions 60 Seconds 1,000 VDC 100 kHz, 1V Min. 1,500 1,000 Units % % % % mV P - P mV P - P mV rms % S % %/C Typ. Max. 65 300 100 Units VDC M pF kHz Units Conditions Min. Typ. -40 +25 -40 +25 -40 Free Air Convection RH, Non-condensing Ambient Case Max. +71 +90 +125 95 C C C Physical Case Size Case Material Weight T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com 1.27 x 0.74 x 0.40 Inches (32.3 x 28.8 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.35 Oz (10g) Conditions MIL HDBK 217F, 25C, Gnd Benign Min. Typ. Max. Units 1.0 MHours UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Reliability Specifications Parameter MTBF Safety Standards Safety Approvals Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec. All Models Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. w w w .D a Min. -0.7 -0.7 -0.7 aS t ee h 4U t om .c % Typ. Max. 25.0 50.0 100.0 260 2500 Units VDC C mW Model Selection Guide Model Number LF301RW LF302RW LF303RW LF304RW LF305RW LF306RW LF307RW LF311RW LF312RW LF313RW LF314RW LF315RW LF316RW LF317RW LF321RW LF322RW LF323RW LF324RW LF325RW LF326RW LF327RW Notes: Reflected Ripple Nominal Range Full-Load No-Load (mA, Typ) 12 9.0 - 18.0 257 20 25 12 9.0 - 18.0 316 20 25 12 9.0 - 18.0 305 20 25 12 9.0 - 18.0 305 20 25 12 9.0 - 18.0 321 20 25 12 9.0 - 18.0 309 20 25 12 9.0 - 18.0 309 20 25 24 18.0 - 36.0 127 5 15 24 18.0 - 36.0 156 5 15 24 18.0 - 36.0 151 5 15 24 18.0 - 36.0 151 5 15 24 18.0 - 36.0 158 5 15 24 18.0 - 36.0 152 5 15 24 18.0 - 36.0 152 5 15 48 36.0 - 75.0 63 3 10 48 36.0 - 75.0 78 3 10 48 36.0 - 75.0 75 3 10 48 36.0 - 75.0 75 3 10 48 36.0 - 75.0 79 3 10 48 36.0 - 75.0 79 3 10 48 36.0 - 75.0 76 3 10 Voltage (VDC) Input Current (mA) Output Voltage Current Current (VDC) (mA, Max) (mA, Min) 3.3 5.0 12.0 15.0 5.0 12.0 15.0 3.3 5.0 12.0 15.0 5.0 12.0 15.0 3.3 5.0 12.0 15.0 5.0 12.0 15.0 700.0 600.0 250.0 200.0 300.0 125.0 100.0 700.0 600.0 250.0 200.0 300.0 125.0 100.0 700.0 600.0 250.0 200.0 300.0 125.0 100.0 70.0 60.0 25.0 20.0 30.0 12.5 10.0 70.0 60.0 25.0 20.0 30.0 12.5 10.0 70.0 60.0 25.0 20.0 30.0 12.5 10.0 Fuse Rating Efficiency Slow-Blow (%, Typ) (mA) 75 79 82 82 78 81 81 76 80 83 83 79 82 82 76 80 83 83 79 82 82 750 750 750 750 750 750 750 350 350 350 350 350 350 350 200 200 200 200 200 200 200 1. When measuring output ripple, it is recommended that an external 0.47 F ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 3.3 F capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR <1.0 at 100 kHz) capacitor be mounted close to the converter. For 12V input units a 3.3 F is recommended, and for 24V & 48V units a 1.5 F. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve Mechanical Dimensions Capacitive Load Single Output F Max 4,700 Dual Output F Max 180 Pin Connections Pin 1 2 3 10 11 12 13 14 15 22 23 24 Single -Vin -Vin NC NC NC NC +Vout NC -Vout NC +Vin +Vin Dual -Vin -Vin NC Common NC -Vout +Vout NC Common NC +Vin +Vin Board Layout NC: No Connection Notes: All dimensions are typical in inches (mm) Tolerance x.xx = 0.01 (0.25) Pin 1 is marked by a "dot" or indentation on the unit Leads are tin plated for improved solderability. MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com |
Price & Availability of LF312RW
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |